2025 Vermeer® Trommel Screens TR5300EM

Information

2025 Vermeer® Trommel Screens TR5300EM

From either control, the operator can choose from four programmable presets or adjust machine settings based on incoming material.

Operators can control the machine through either the Vermeer DP10 display mounted on the control panel.

The TR5300EM features a large, low feed height hopper that makes it easier to load with a loading ramp, making the trommel screen more mobile around the jobsite.

The hydraulic-driven chain drive system provides positive drum drive and allows the drum to lift off of the cog for service and maintenance.

From the dual-hinged doors on either side of the machine, you can perform machine maintenance efficiently through ease of access to components such as motor, trommel drum and drum drive.

Without having to change out the drum, you can adjust the screen panel quickly which will allow operators to change opening size, wire gauge and type of wire so you can separate a wide variety of material.

Powered by an industrial-duty, fully enclosed and fan-cooled electric motor. A single 60-hp (44.5-kW) motor powers the hydraulic pump stack. Electric motors reduce exhaust emissions, jobsite noise and maintenance compared to diesel.

Features may include:

  • Electric-powered efficiency
  • Quiet operation for wherever the job may take you
  • Complete control for overall jobsite confidence

Photos

Highlights

  • Blackshear, Georgia
  • 2025
  • Vermeer®
  • Trommel Screens TR5300EM
  • Available
  • Operation: 112.8 in | Conveyor Belt: 36 in | Hopper Opening: 37-in | Drum Support Description: 4-in (10.2-cm) | Head Pulley: 38-in (96.5-cm) | Self-Cleaning Tail Pulley Dimensions: 38-in (96.5-cm)
  • Operation: 15 ft | Hopper: 9.5 ft (2.9 m) | Conveyor Belt Stacking: 15 ft | Hopper Opening: 34-in

Specifications

  • 2025
  • Vermeer®
  • Trommel Screens
  • TR5300EM
  • General
  • Siemens
  • Conveyor: 33 cu-in
  • Rating: 480 VAC, 3 Phase, 60 Hz, 60 hp (44.7 kW), 177 lb-ft (240 Nm) at 1800 rpm
  • Single leaf sprung
  • 445/50R22.5
  • System Voltage: 12 V | AC panel: 75 hp, 480 VAC, soft start
  • Drum: 0-24 rpm | Fines Belt: 500 ft/min
  • Drum Operation: 0-30.9 gpm (0-117 L/min) | Conveyor Operation: 17 gpm
  • Heavy-duty structural tubing | Fines Conveyor Frame: 2 in (5.1 cm) x 8 in (20.3 cm) structural steel tubing
  • Drum Diameter: 5 ft | Drum Support Description: 8-in (20.3-cm) diameter | Thrust Bearing Diameter: 4 in | Thrust Bearing Face: 2.9 in | Drum Angle Adjustability: 0-7 deg | Brush Diameter: 14 in | Brush Assembly Support: Two 1.25-in (2.3-cm) sealed ball bearings | Head Pulley: 12-in (30.5-cm) diameter | Head Pulley Bearing: 2 7/16-in (6.2-cm) pillow block | Self-Cleaning Tail Pulley Dimensions: 10-in (25.4-cm) diamater, 2 7/16-in (6.1-cm) shaft | Head Pulley Takeup: 10 in | Self-Cleaning Return Idlers: 4-in (10.2-cm) rubber disc
  • 39 ft
  • 98.4 in
  • 13.4 ft
  • Bottom: 37 in
  • Operation: 89.9 ft | Drum: 15 ft | Fines Conveyor: 55 ft
  • Operation: 112.8 in | Conveyor Belt: 36 in | Hopper Opening: 37-in | Drum Support Description: 4-in (10.2-cm) | Head Pulley: 38-in (96.5-cm) | Self-Cleaning Tail Pulley Dimensions: 38-in (96.5-cm)
  • Operation: 15 ft | Hopper: 9.5 ft (2.9 m) | Conveyor Belt Stacking: 15 ft | Hopper Opening: 34-in
  • 5.5 cu yd
  • Tank: 55 gal
  • Drum Support Description: Eight poly trunnion rollers | Drum Drive Chain: 140 custom extended pin | Maximum Screen Panels: 4 | Head Pulley Type: Rubber-lagged | Troughing Idler Type: 20-deg CEMA "B" with permanently seated bearings | Self-Cleaning Return Idlers: qty 8
  • 100 cu yd (76.5 m3) per hr with 0.5-in (12.7-mm) screens installed and material with moisture less than 40%
  • 32000 lbs | Hitch: 11600 lbs
  • Bristle: Polyethylene