2025 Vermeer® Brush Chippers BC1000XL

Information

2025 Vermeer® Brush Chippers BC1000XL

Equipped with a powerful 72.4-hp (54-kW) Deutz® 2.9 L4 gas engine, the chipper boasts a reliable electronic fuel injection (EFI) system for cold-weather starts and superior fuel efficiency compared to carbureted gas engines.

Spend less time maintaining with a clutchless PTO system that helps prevent premature wear on the belt drive by only allowing engagement at low idle.

The BC1000XL comes with a 25-gal (94.6-L) fuel tank that lets you put in more hours before refueling.

The EcoIdle™ engine control system reduces engine speed to a preset lower rpm after one to five minutes of inactivity, saving fuel and reducing jobsite noise.

SmartFeed, a patented feed-sensing control system, boosts operator productivity and reduces engine strain by monitoring engine rpm and controlling feed rollers.

The patented bottom feed stop bar is strategically positioned so the operator can strike it to shut off the feed mechanism.

VermeerOne™ Platform isn’t just a tool or platform. It’s an experience — one designed to simplify equipment management, empower users with real time data to make smarter decisions, and help maximize productivity and profitability.

Features may include:

  • Feed with machine intelligence for maximum productivity
  • Spend less time maintaining and more time working
  • Safety features designed with the operator in mind

Photos

Highlights

  • Blackshear, Georgia
  • 2025
  • Vermeer®
  • Brush Chippers BC1000XL
  • Tongue Description: 2.5" x 4.5" x .25" (6.4 cm x 11.4 cm x .6 cm) / Extension: Extendable 24" (61 cm) at 12" (30.5 cm) increments
  • Available
  • 66.5 in | Infeed Table: 52 in | 20 in
  • 101 in | Infeed Hopper: 12 in | Chute: 101 in

Specifications

  • 2025
  • Vermeer®
  • Brush Chippers
  • BC1000XL
  • Brush
  • 2.4 in
  • 28.3
  • Manufacturer: White
  • Torsion
  • Group 24; 580 CCA
  • System Voltage: 12 Volt
  • Feed: 118 ft/min | 2220 rpm
  • Actuation Force (BFSB): 34 lbs
  • System Type: Open center
  • Pump Flow at Maximum RPM: 3 gpm
  • System relief: 2500 psi
  • Tongue Description: 2.5" x 4.5" x .25" (6.4 cm x 11.4 cm x .6 cm) / Extension: Extendable 24" (61 cm) at 12" (30.5 cm) increments
  • 7" (17.8 cm) Z channel; .25" (0.6 cm) thickness
  • Pintle
  • Maximum Angle of Continuous Operation: 30 deg | Feed Roller Minimum Distance to Drum: 1 in | Feed Roller: 20 " x 17 " (50.8 cm x 43.2 cm) | Infeed Throat Capacity: 12 " x 17.5 " (30.5 cm x 43.2 cm) | Pinch Point - Distance to End of Feed Table: 66.5 in | Distance from Feed Table to Ground: 26 in | Infeed Table Material Thickness: .2 in | Bottom Feed Stop Bar Diameter: 2 in | Bottom Feed Stop Bar Material Thickness: 11 GA | Normal Sensitivity: 22 deg | Reduced Sensitivity: 12 deg | Material Capacity: 12 in | Thickness: 20 in | Diameter: 20 in | Knife Thickness: .6 in | Knife Size: 0.63 " x 4.5 " x 9 " (1.6 cm x 11.4 cm x 22.9 cm) | Bedknife Size: 3.5 " x 17.3 " (8.9 cm x 43.8 cm) | Bedknife Thickness: 1 in | Chute Rotation Angle: 270 deg
  • Feed Table Up, Tongue In: 160 in | Table Down, Tongue Extended: 208 in | Infeed Table: 32 in
  • 66.5 in | Infeed Table: 52 in | 20 in
  • 101 in | Infeed Hopper: 12 in | Chute: 101 in
  • 18.75-in suction
  • 20 gal
  • Volume with Filter: 8 qt
  • 5.5 gal
  • Feed Roller Orientation: Horizontal | Number of Feed Rollers: 1 | Number of Feed Roller Motors: 1 | Reset Method: Green hold-to-run button | Positions: 4: E-stop, forward, neutral, and reverse | Safety Lock - Number of Positions: 2 | Useable Edges: 2 | Number of Paddles: 5 | Fixture Method: Weld-on | Bedknife - Number of Useable Edges: 4 | Number of Bearings: 2 | Type: Spherical rollers | Rotation Type: Manual rotate with pin lock | Filtration Method: 10 micron return; 100 micron suction | Sound Power 119 dB(A) | Controller: Vermeer ACS | Shutdown System: High temp, low pressure
  • Feed Roller Clamp Load: 350 lbs | Static: 53500 lbs
  • 7 gal
  • Of Feed Roller: 400 lbs | With Shaft: 460 lbs
  • Recommended: 10W30 | hydraulic Recommended: Vermeer VMF
  • A8 chipper steel | Bedknife: 1018 | Fender Description: Bolt-on steel
  • 5V
  • 2 | Number of Bolts/Knife: 4