2025 Vermeer® Brush Chippers BC1200XL

Information

2025 Vermeer® Brush Chippers BC1200XL

A powerful 115-hp (85.8-kW) Origin® engine with electronic fuel injection enhances fuel economy and boosts engine response under load.

Get more done thanks to the aggressive feeding action of dual horizontal offset feed rollers that can be adjusted for optimal clamping force when feeding.

SmartFeed, a patented feed-sensing control system, boosts operator productivity and reduces engine strain by monitoring engine rpm and controlling feed rollers.

The EcoIdle™ engine control system reduces engine speed to a preset lower rpm after one to five minutes of inactivity, saving fuel and reducing jobsite noise.

The patented bottom feed stop bar is strategically positioned so the operator can strike it to shut off the feed mechanism.

VermeerOne™ Platform isn’t just a tool or platform. It’s an experience — one designed to simplify equipment management, empower users with real time data to make smarter decisions, and help maximize productivity and profitability.

Features may include:

  • Get more done with the aggressive feeding action
  • Intelligent feeding for the toughest jobs
  • Safety features designed with the operator in mind

Photos

Highlights

  • Blackshear, Georgia
  • 2025
  • Vermeer®
  • Brush Chippers BC1200XL
  • Tongue Description: 2.5" x 4.5" x 0.38" (6.4 cm x 11.4 cm x 9.5 mm) | Tongue Extension: Extendable 18" (45.7 cm) | Fender Description: Bolt-on
  • Available
  • 79 in | Infeed Table: 52 in | Drum: 20 in
  • 103 in | Infeed Hopper: 32 in | Chute: 104 in

Specifications

  • 2025
  • Vermeer®
  • Brush Chippers
  • BC1200XL
  • Brush
  • Manufacturer: White Hydraulic
  • Torsion
  • Group 31; 950 CCA
  • System Voltage: 12 volt | Switches: Lower feed stop bar senstivity, toggle, SmartFeed and Ecoldle | Controller: Vermeer ACS | Display: LCD | Shutdown System: High temperature, low pressure
  • 70 Amp
  • 2000 rpm | Feed: 110 ft/min
  • Actuation Force: 34 lbs
  • 124 dB(a)
  • System Type: Open center, dual pumps
  • Pump Flow at Maximum RPM: 4.1 gpm
  • System relief: 2500 psi | Auto Reverse: 2500 psi
  • 2000 cfm
  • Tongue Description: 2.5" x 4.5" x 0.38" (6.4 cm x 11.4 cm x 9.5 mm) | Tongue Extension: Extendable 18" (45.7 cm) | Fender Description: Bolt-on
  • 7" (17.78) Z channel; 0.25" (0.64 cm) thickness
  • Pintle
  • Lock - Number of Positions: 2
  • Feed Roller Minimum Distance to Drum: 1 in | Feed Roller Dimension: 15 | Feed Roller Dimension (Two): 11.1" (28.3 cm) | Infeed Throat Capacity: 13.3" x 17" (33.7 cm x 43.2 cm) | Pinch Point - Distance to End of Feed Table: 67.4 in | Distance from Feed Table to Ground: 27.2 in | Infeed Table Material Thickness: .2 in | Bottom Feed Stop Bar Diameter: 2 in | Bottom Feed Stop Bar Material Thickness: 11 GA | Normal Sensitivity: 22 deg | Reduced Sensitivity: 12 deg | Diameter: 2 in | Material Thickness: .1 in | Material Capacity: 13.3 in | Thickness: .4 in | drum: 20 in | Knife Thickness: .6 in | Knife Size: .625" x 4.5" x 9" (1.6 cm x 11.4 cm x 22.9 cm) | Bedknife Size: 3.5" x 17.3" (8.9 cm x 43.8 cm) | Bedknife Thickness: 1 in | Bottom Thickness: .1 in | Top Thickness: .1 in | Side Wall Thickness: .1 in | Deflector Thickness: .1 in | Chute Rotation Angle: 270 deg
  • Feed Table Up, Tongue In: 168 in | Table Down, Tongue Extended: 206 in | Infeed Table: 30.1 in
  • 79 in | Infeed Table: 52 in | Drum: 20 in
  • 103 in | Infeed Hopper: 32 in | Chute: 104 in
  • 19" sucker
  • Oil Volume with Filter: 7.8 qt
  • Coolant Capacity (Engine and Radiator): 4 gal
  • Feed Roller Clamp Load: 2650 lbs
  • Tank: 12 gal
  • Of Feed Roller: 150 lbs | With Shaft: 480 lbs
  • Feed Roller Orientation: Horizontal | Number of Feed Rollers: 2 | Feed Roller Clamp Type: Hydraulic cylinder | Number of Feed Roller Motors: 2 | Reset Method: Dual green hold-to-run buttons | Positions: Four positions: Emergency stop, forward, and reverse | Useable Edges: 2 | Number of Paddles: 5 | Fixture Method: Weld-on | Bedknife - Number of Useable Edges: 4 | Number of Bearings: 2 | Rotation Type: Manual pivot with handle | Filtration Method: 10 micron return, 100 micron suction
  • Recommended: SAE 10W30 | hydraulic Recommended: Vermeer VMF
  • A8 chipper steel | Bedknife Material: 1018
  • 8 / 2: 12 | Number of Bolts/Knife: 4