2025 Vermeer® Brush Chippers BC900XL

Information

2025 Vermeer® Brush Chippers BC900XL

SmartFeed, a patented feed-sensing control system, boosts operator productivity and reduces engine strain by monitoring engine rpm and controlling feed rollers.

The large infeed opening simplifies feeding irregular material and reduces the need for crosscuts before feeding the chipper.

Designed with ease of maintenance in mind, the BC900XL features a dripless oil filter and conveniently located grease points to help reduce service time.

The patented bottom feed stop bar is strategically positioned so the operator can strike it to shut off the feed mechanism.

VermeerOne™ Platform isn’t just a tool or platform. It’s an experience — one designed to simplify equipment management, empower users with real time data to make smarter decisions, and help maximize productivity and profitability.

Features may include:

  • Enhanced chipping capabilities
  • Optimal access to key machine maintenance areas
  • Safety features built with the operator in mind

Photos

Highlights

  • Blackshear, Georgia
  • 2025
  • Vermeer®
  • Brush Chippers BC900XL
  • Tongue Description: 3" x 5" 3/16" (7.6 cm x 12.7 cm x .5 cm) Tube
  • Gasoline
  • Available
  • 79.5 in | Infeed Table: 48 in
  • 97 in | Infeed Hopper: 32 in | Chute: 96.7 in

Specifications

  • 2025
  • Vermeer®
  • Brush Chippers
  • BC900XL
  • Brush
  • 3925 cfm
  • 2.2 in
  • Briggs and Stratton Vanguard
  • Gross Horsepower (Maximum): 35 hp
  • 53 ft-lb
  • Engine-mounted
  • Spin-On
  • Medium: Air
  • 33.1 CID
  • Manufacturer: White
  • Max Fuel Consumption: 3.2 gph
  • Gasoline
  • Drive Engagement: Clutchless PTO
  • 3500 lb (1587.6 kg)
  • Group 24 - 580 CCA
  • System: 12 V
  • 20 amp
  • Feed: 140 ft/min | 1500 rpm
  • Actuation Force (BFSB): 34 lbs
  • System Type: Tandem Center
  • Pump Flow at Maximum RPM: 5 gpm
  • System relief: 2500 psi | Auto Reverse PSI: 2300 psi
  • Tongue Description: 3" x 5" 3/16" (7.6 cm x 12.7 cm x .5 cm) Tube
  • 3/16 in. x 5-5/8 in. (.5 cm x 14.3 cm)
  • Pintle or ball
  • Feed Roller Dimension: 15.8" dia x 13.5" long (40 cm x 34.3 cm) | Infeed Throat Capacity: 9 in x 14 in (22.9 cm x 35.6 cm) | Pinch Point - Distance to End of Feed Table: 65 in | Distance from Feed Table to Ground: 29 in | Infeed Table Material Thickness: .2 in | Bottom Feed Stop Bar Diameter: 2 in | Bottom Feed Stop Bar Material Thickness: 11 GA | Normal Sensitivity: 22 deg | Reduced Sensitivity: 12 deg | Diameter: 2 in | Material Thickness: .1 in | Material Capacity: 9 in | Thickness: 1 in | Diameter: 33 in | Knife Thickness: .6 in | Knife Size: 5" x 11.75" (12.7 cm x 29.8 cm) | Bedknife Size: 5" x 12.1" (12.7 cm x 30.7 cm) horizontal and 5" x 8.8" (12.7 cm x 22.4 cm) vertical | Bedknife Thickness: .8 in | Bottom Thickness: .1 in | Top Thickness: .1 in | Side Wall Thickness: .1 in | Deflector Thickness: .1 in | Chute Rotation Angle: 270 deg
  • Feed Table Up, Tongue In: 140.4 in | Table Down, Tongue Extended: 154.8 in | Infeed Table: 26 in
  • 79.5 in | Infeed Table: 48 in
  • 97 in | Infeed Hopper: 32 in | Chute: 96.7 in
  • 16 gal
  • Oil Volume with Filter: 2.9 qt
  • Feed Roller Orientation: Horizontal | Number of Feed Rollers: 1 | Feed Roller Clamp Type: Spring/weight | Number of Feed Roller Motors: 1 | Reset Method: Dual green hold-to-run buttons | Positions: Four positions: Emergency stop, forward, stop and reverse | Safety Lock - Number of Positions: 6 | Useable Edges: 2 | Number of Paddles: 2 | Fixture Method: Bolt-on | Bedknife - Number of Useable Edges: 2 | Number of Bearings: 2 | Rotation Type: Manual dual handles with pin lock | Filtration Method: 10 micron return | Fender Description: Bolt-on
  • Feed Roller Clamp Load: 560 lbs
  • 6.8 gal
  • Of Feed Roller: 210 lbs | With Shaft: 330 lbs
  • Recommended: 10W30 | Vermeer VMF Gold
  • A8 chipper steel | Bedknife: Grade 50
  • Chipper - Polyester Cord with wrap
  • 12 | 2 | Number of Bolts/Knife: 5