Motor
Displacement
28.4
Motor Type
Manufacturer: White RE470
Suspension
Suspension
Torflex
Electric
Electrical
System Voltage: 12 | Switches: Control Panel: Ignition, throttle, Smartfeed, exhaust regeneration, and ECOIdle. Rear: Lower feed bar sensitivity | Display: MFD | Controller: Vermeer ACS: CB02 | Shutdown System: High temp, low pressure
Operating Speed
1100 | Feed: 117 ft/min
Hydraulics
Hydraulic Type
System Type: Open Center
Hydraulic Pump
Pump Flow at Maximum RPM: 6.3 gpm
Maximum Pressure
System relief: 2800 psi | Auto Reverse: 2400 psi
Airflow
3544 cfm
Chassis
Chassis
Tongue Description: 4 x 4 x 0.375 / Extension: Two 12" Increments (for non winch)
Frame Type
7" x 2.13" Channel
Hitch/Type
Pintle
Lights and Safety
Safety Features
Safety Lock - Number of Positions: 4 | Rotational Lock: Self Lock
Dimensions
Dimensions
Maximum Angle of Continuous Operation: 30 deg | Feed Roller Dimension: 23.5" x 18 | Feed Roller Dimension (Two): 23.5" x 18 | Infeed Throat Capacity: 20" x 24" | Distance from Feed Table to Ground: 30.5 in | Infeed Table Material Thickness: .2 in | Bottom Feed Stop Bar Diameter: 2 in | Bottom Feed Stop Bar Material Thickness: 11 GA | Normal Sensitivity: 22 deg | Reduced Sensitivity: 12 deg | diameter: 2 in | Material Thickness: 11 in | Material Capacity: 19 in | Thickness: 26.1 in | Diameter: 36 in | Knife Thickness: .6 in | Knife Size: 0.625 x 5 x 10 | Bedknife Size: 3" x 20.25" | Bedknife Thickness: 1.3 in | Bottom Thickness: .1 in | Top Thickness: .3 in | Side Wall Thickness: .1 in | Deflector Thickness: .1 in | Chute Rotation Angle: 270 deg
Length
Feed Table Up, Tongue In: 177 in | Table Down, Tongue Extended: 231 in | Infeed Table: 36 in
Width
78.5 in | Infeed Table: 67 in | drum: .5 in
Height
107 in | Infeed Hopper: 34 in | Chute: 110 in
Capacities
Fuel Capacity
35 gal
Load Capacity, Land
Feed Roller Clamp Load: 380 lbs
Hydraulic Capacity
Tank: 12 gal
Weights
Weight
Without winch and hydraulic jack: 9600 lbs | with winch, hydraulic jack and hydraulic chute: 10366 lbs | of Feed Roller: 116 lbs | With Shaft: 1160 lbs
Features
Features
Number of Feed Rollers: 2 | Feed Roller Clamp Type: Spring | Number of Feed Roller Motors: 2 | Reset Method: Green Hold to Run Button | Positions: 4: E-Stop, Forward, Neutral, Reverse | Useable Edges: 2 | Number of Paddles: 12 | Fixture Method: Weld on | Bedknife - Number of Useable Edges: 4 | Number of Bearings: 2 | Rotation Type: Worm gear with rotational lock | Filtration Method: 3 micron return, 100 micron suction
Oil Type
Recommended: ACEA E-7 & E-6 or API CI-4 | Recommended hydraulic: Vermeer VMF
Construction Material
A8 Modified Chipper Steel | Bedknife: 1018 CD
Knife Quantity
11 | 4 | Number of Bolts/Knife: 5
Belt Type
Belt Idler/Tensioner: Spring loaded | 5V