2025 Vermeer® Brush Chippers BC1800XL Tier 4 Final

Information

2025 Vermeer® Brush Chippers BC1800XL Tier 4 Final

Minimize vibration and structural stress on the rear of the machine with vertical feed rollers featuring helical cleats that firmly grip the material.

SmartFeed, a patented feed-sensing control system, boosts operator productivity and reduces engine strain by monitoring engine rpm and controlling feed rollers.

The EcoIdle™ engine control system reduces engine speed to a preset lower rpm after one to five minutes of inactivity, saving fuel and reducing jobsite noise.

The patented bottom feed stop bar is strategically positioned so the operator can strike it to shut off the feed mechanism.

VermeerOne™ Platform isn’t just a tool or platform. It’s an experience — one designed to simplify equipment management, empower users with real time data to make smarter decisions, and help maximize productivity and profitability.

Features may include:

  • Built for jobsites with large-diameter chipping
  • Intelligent chipping for increased productivity
  • Take control when the jobsite demands it

Photos

Highlights

  • Blackshear, Georgia
  • 2025
  • Vermeer®
  • Brush Chippers BC1800XL Tier 4 Final
  • Tongue Description: 4 x 4 x 0.375 / Extension: Two 12" Increments (for non winch)
  • Available
  • 78.5 in | Infeed Table: 67 in | drum: .5 in
  • 107 in | Infeed Hopper: 34 in | Chute: 110 in

Specifications

  • 2025
  • Vermeer®
  • Brush Chippers
  • BC1800XL Tier 4 Final
  • Brush
  • 28.4
  • Manufacturer: White RE470
  • Torflex
  • System Voltage: 12 | Switches: Control Panel: Ignition, throttle, Smartfeed, exhaust regeneration, and ECOIdle. Rear: Lower feed bar sensitivity | Display: MFD | Controller: Vermeer ACS: CB02 | Shutdown System: High temp, low pressure
  • 1100 | Feed: 117 ft/min
  • System Type: Open Center
  • Pump Flow at Maximum RPM: 6.3 gpm
  • System relief: 2800 psi | Auto Reverse: 2400 psi
  • 3544 cfm
  • Tongue Description: 4 x 4 x 0.375 / Extension: Two 12" Increments (for non winch)
  • 7" x 2.13" Channel
  • Pintle
  • Safety Lock - Number of Positions: 4 | Rotational Lock: Self Lock
  • Maximum Angle of Continuous Operation: 30 deg | Feed Roller Dimension: 23.5" x 18 | Feed Roller Dimension (Two): 23.5" x 18 | Infeed Throat Capacity: 20" x 24" | Distance from Feed Table to Ground: 30.5 in | Infeed Table Material Thickness: .2 in | Bottom Feed Stop Bar Diameter: 2 in | Bottom Feed Stop Bar Material Thickness: 11 GA | Normal Sensitivity: 22 deg | Reduced Sensitivity: 12 deg | diameter: 2 in | Material Thickness: 11 in | Material Capacity: 19 in | Thickness: 26.1 in | Diameter: 36 in | Knife Thickness: .6 in | Knife Size: 0.625 x 5 x 10 | Bedknife Size: 3" x 20.25" | Bedknife Thickness: 1.3 in | Bottom Thickness: .1 in | Top Thickness: .3 in | Side Wall Thickness: .1 in | Deflector Thickness: .1 in | Chute Rotation Angle: 270 deg
  • Feed Table Up, Tongue In: 177 in | Table Down, Tongue Extended: 231 in | Infeed Table: 36 in
  • 78.5 in | Infeed Table: 67 in | drum: .5 in
  • 107 in | Infeed Hopper: 34 in | Chute: 110 in
  • 35 gal
  • Feed Roller Clamp Load: 380 lbs
  • Tank: 12 gal
  • Without winch and hydraulic jack: 9600 lbs | with winch, hydraulic jack and hydraulic chute: 10366 lbs | of Feed Roller: 116 lbs | With Shaft: 1160 lbs
  • Number of Feed Rollers: 2 | Feed Roller Clamp Type: Spring | Number of Feed Roller Motors: 2 | Reset Method: Green Hold to Run Button | Positions: 4: E-Stop, Forward, Neutral, Reverse | Useable Edges: 2 | Number of Paddles: 12 | Fixture Method: Weld on | Bedknife - Number of Useable Edges: 4 | Number of Bearings: 2 | Rotation Type: Worm gear with rotational lock | Filtration Method: 3 micron return, 100 micron suction
  • Recommended: ACEA E-7 & E-6 or API CI-4 | Recommended hydraulic: Vermeer VMF
  • A8 Modified Chipper Steel | Bedknife: 1018 CD
  • 11 | 4 | Number of Bolts/Knife: 5
  • Belt Idler/Tensioner: Spring loaded | 5V